Research Articles | Challenge Journal of Structural Mechanics

The mechanical properties of cement mortar reinforced with silica fume subjected to sulfate and chloride environment

Sulaiman Al-Safi, Abdulghani Altharehi, Ibrahim A. Alameri, Abdulmalek Al-Jolahy


DOI: https://doi.org/10.20528/cjsmec.2025.01.005
View Counter: Abstract | 108 times | ‒ Full Article | 21 times |

Full Text:

PDF

Abstract


This study investigates the effect of incorporating micro-sized silica fume on the mechanical properties and durability of cement mortar when exposed to sulfate and chloride environments. Mortar samples were prepared by replacing cement with micro-sized silica fume in varying proportions of 5%, 10%, 15%, 20%, 25%, 30%, and 35% by weight. The specimens were cured in water and chemically aggressive conditions, including 5% and 10% sodium sulfate solutions, as well as mixtures of 5% and 10% sodium chloride solutions, to simulate real-world exposure to such environments. Experimental results revealed that the addition of silica fume significantly enhanced the mortar's resistance to chemical deterioration caused by sulfates and chlorides. This improvement is attributed to the pozzolanic reaction of silica fume, which contributed to denser microstructures, reduced porosity, and a stronger bond within the matrix. Among the tested proportions, the optimal replacement ratios for achieving the best balance between mechanical strength and durability were identified up to 20%. These findings highlight the efficiency of silica fume as a supplementary cementitious material in mitigating the adverse effects of aggressive chemical agents. Such modifications can be particularly valuable in improving the service life of concrete structures exposed to harsh environmental conditions, enhancing sustainability and cost-effectiveness in construction practices.


Keywords


cement mortar; silica fume; sulfate attack; chloride attack; reactivity

References


Abed M, Nasr M, Hasan Z (2018). Effect of silica fume/binder ratio on compressive strength development of reactive powder concrete under two curing systems. MATEC Web of Conferences, 162, 02022.

Alameri I, Oltulu M, Ardahanlı M (2020). Influence of preheating on the mechanical properties of high strength concrete with micro silica filler. Bilecik Seyh Edebali University Journal of Science, 7(2), 1084-1093.

Al-Saffar FY, Wong LS, Paul SC (2023). An elucidative review of the nanomaterial effect on the durability and calcium-silicate-hydrate (CSH) gel development of concrete. Gels, 9(8), 613.

Anwar M (2005). Effect of cementitious materials on concrete against sulfate attack. Engineering Research Journal, 99, C92-C104.

ASTM C109/C109M-20 (2020). Standard test method for compressive strength of hydraulic cement mortars (using 2-in. or [50-mm] cube specimens). ASTM International, West Conshohocken, PA.

ASTM C143/C143M-20 (2020). Standard test method for slump of hydraulic-cement concrete. ASTM International, West Conshohocken, PA.

ASTM C150/C150M-24 (2024). Standard specification for portland cement. ASTM International, West Conshohocken, PA.

ASTM C597-22 (2022). Standard test method for ultrasonic pulse velocity through concrete. ASTM International, West Conshohocken, PA.

ASTM C642-21 (2021). Standard Test method for density, absorption, and voids in hardened concrete. ASTM International, West Conshohocken, PA.

ASTM C1585-20 (2020). Standard test method for measurement of rate of absorption of water by hydraulic-cement concretes. ASTM International, West Conshohocken, PA.

ASTM D790-17 (2017). Standard test methods for flexural properties of unreinforced and reinforced plastics and electrical insulating materials. ASTM International, West Conshohocken, PA.

ASTM E494-20 (2020). Standard practice for measuring ultrasonic velocity in materials by comparative pulse-echo method. ASTM International, West Conshohocken, PA.

Atabey İ, Çelikten S, Canbaz M (2023). Chemical resistance of hardened mortar containing andesite and marble industry waste powder. Challenge Journal of Concrete Research Letters, 14(2), 31-38.

Atasever M, Tokyay M (2024). Determining datum temperature and apparent activation energy: an approach for mineral admixtures incorporated cementitious systems. Challenge Journal of Concrete Research Letters, 15(4), 142-149.

Feng L, Zhao P, Wang Z, Gao J, Su X, Li H (2018). Improvement of mechanical properties and chloride ion penetration resistance of cement pastes with the addition of pre-dispersed silica fume. Construction and Building Materials, 182, 483-492.

Güney B, Yıldızel S (2024). Optimization of mechanical properties in lime-based composites using the Taguchi method. Challenge Journal of Structural Mechanics, 10(3), 109-115.

Hamada HM, Abed F, Katman HYB, Humada AM, AlJawahery MS, Majdi A, Yousif ST, Thomas BS (2023). Effect of silica fume on the properties of sustainable cement concrete. Journal of Materials Research and Technology, 24, 8887-8908.

Han M, Li J (2024). Enhancement of compressive strength and durability of sulfate-attacked concrete. Buildings, 14(7), 2187.

Harirchian E (2024). Predicting compressive strength of AAC blocks through machine learning advancements. Challenge Journal of Concrete Research Letters, 15(2), 56-68.

Lee, FH, Lee Y, Chew SH, Yong KY. (2005). Strength and modulus of marine clay-cement mixes. Journal of Geotechnical and Geoenvironmental Engineering, 131(2), 178–186.

Lou Y, Khan K, Amin MN, Ahmad W, Deifalla AF, Ahmad A (2023). Performance characteristics of cementitious composites modified with silica fume: A systematic review. Case Studies in Construction Materials, 18, e01753.

McCarthy MJ, Dyer TD (2019). Pozzolanas and pozzolanic materials. In: Hewlett PC, Liska M, editors. Lea’s Chemistry of Cement and Concrete (5th edition), Butterworth-Heinemann, Oxford, United Kingdom, 363-467.

Ortega JM, Esteban MD, Williams M, Sánchez I, Climent MÁ (2018). Short-term performance of sustainable silica fume mortars exposed to sulfate attack. Sustainability, 10(7), 2517.

Ramezanianpour, AA, Riahi Dehkordi E, Ramezanianpour AM (2020). Influence of sulfate ions on chloride attack in concrete mortars containing silica fume and jajrood trass. Iranian Journal of Science and Technology, Transactions of Civil Engineering, 44(4), 1135–1144.

Saif Allah JS, Kassim MM, Salman GA (2024). The durability of concrete mortars with different mineral additives exposed to sulfate attack. Salud, Ciencia y Tecnología - Serie De Conferencias, 3, 851.

Shannag M, Shaia HA (2003). Sulfate resistance of high-performance concrete. Cement and Concrete Composites, 25(3), 363-369.

Sharaky IA, Megahed FA, Seleem MH, Badawy AM (2019). The influence of silica fume, nano silica and mixing method on the strength and durability of concrete. SN Applied Sciences, 1(6), 575.

Shetti, AP, Das BB. (2015). Acid, alkali and chloride resistance of early age cured silica fume concrete. In: Matsagar V, editor. Advances in Structural Engineering. Springer India, New Delhi, India, 1849-1862.

Şimşek O, Aruntaş HY, Demir İ, Yaprak H, Yazıcıoğlu S (2022). Investigation of the effect of seawater and sulfate on the properties of cementitious composites containing silica fume. Silicon, 14(2), 663–675.

Tripathi D, Kumar R, Mehta PK, Singh A (2020). Silica fume mixed concrete in acidic environment. Materials Today: Proceedings, 27, 1001–1005.

Zhou ZY, Gencturk B, Willam K, Attar A (2015). Carbonation-induced and chloride-induced corrosion in reinforced concrete structures. Journal of Materials in Civil Engineering, 27(9), 04014245.


Refbacks

  • There are currently no refbacks.